In materials like aluminium and copper, the correct order of magnitude of various elastic modului is:

Question:

In materials like aluminium and copper, the correct order of magnitude of various elastic modului is:

  1. Young’s modulus $<$ shear modulus $<$ bulk modulus.

  2. Bulk modulus $<$ shear modulus $<$ Young’s modulus

  3. Shear modulus $<$ Young’s modulus $<$ bulk modulus.

  4. Bulk modulus $<$ Young’s modulus $<$ shear modulus.

JEE Main Previous Year Single Correct Question of JEE Main from Physics Mechanical Properties of Solids chapter.

JEE Main Previous Year April 9, 2014


Correct Option: 3

Solution:

Related Questions

  • If the potential energy between two molecules is given by $U=-\frac{A}{r^{6}}+\frac{B}{r^{12}}$, then at equilibrium, separation between molecules, and the potential energy are:

    View Solution

  • A uniform cylindrical rod of length $\mathrm{L}$ and radius $r$, is made from a material whose Young’s modulus of Elasticity equals $Y$. When this rod is heated by temperature $T$ and simultaneously subjected to a net longitudinal compressional force $\mathrm{F}$, its length remains unchanged. The coefficient of volume expansion, of the material of the rod, is (nearly) equal to:

    View Solution

  • In an environment, brass and steel wires of length $1 \mathrm{~m}$ each with areas of cross section $1 \mathrm{~mm}^{2}$ are used. The wires are connected in series and one end of the combined wire is connected to a rigid support and other end is subjected to elongation. The stress required to produce a net elongation of $0.2 \mathrm{~mm}$ is,

    [Given, the Young’s modulus for steel and brass are, respectively, $120 \times 10^{9} \mathrm{~N} / \mathrm{m}^{2}$ and $60 \times 10^{9} \mathrm{~N} / \mathrm{m}^{2}$ ]

    View Solution

  • The elastic limit of brass is $379 \mathrm{MPa}$. What should be the minimum diameter of a brass rod if it is to support a 400 $\mathrm{N}$ load without exceeding its elastic limit?

    View Solution

  • A steel wire having a radius of $2.0 \mathrm{~mm}$, carrying a load of $4 \mathrm{~kg}$, is hanging from a ceiling. Given that $\mathrm{g}=3.1 \mathrm{~A} \mathrm{~ms}^{-2}$, what will be the tensile stress that would be developed in the wire?

    View Solution

  • Young’s moduli of two wires $A$ and $B$ are in the ratio $7: 4$. Wire $\mathrm{A}$ is $2 \mathrm{~m}$ long and has radius $\mathrm{R}$. Wire $\mathrm{B}$ is $1.5 \mathrm{~m}$ long and has radius $2 \mathrm{~mm}$. If the two wires stretch by the same length for a given load, then the value of $R$ is close to :

    View Solution

  • As shown in the figure, forces of $10^{5} \mathrm{~N}$ each are applied in opposite directions, on the upper and lower faces of a cube of side $10 \mathrm{~cm}$, shifting the upper face parallel to itself by $0.5 \mathrm{~cm}$. If the side of another cube of the same material is, $20 \mathrm{~cm}$, then under similar conditions as above, the displacement will be:

    View Solution

  • A thin $1 \mathrm{~m}$ long rod has a radius of $5 \mathrm{~mm}$. A force of $50 \pi \mathrm{kN}$ is applied at one end to determine its Young’s modulus. Assume that the force is exactly known. If the least count in the measurement of all lengths is $0.01 \mathrm{~mm}$, which of the following statements is false ?

    View Solution

  • A uniformly tapering conical wire is made from a material of Young’s modulus Y and has a normal, unextended length

    L. The radii, at the upper and lower ends of this conical wire, have values $R$ and $3 R$, respectively. The upper end of the wire is fixed to a rigid support and a mass $M$ is suspended from its lower end. The equilibrium extended length, of this wire, would equal :

    View Solution

  • The pressure that has to be applied to the ends of a steel wire of length $10 \mathrm{~cm}$ to keep its length constant when its temperature is raised by $100^{\circ} \mathrm{C}$ is:

    (For steel Young’s modulus is $2 \times 10^{11} \mathrm{Nm}^{-2}$ and coefficient of thermal expansion is $1.1 \times 10^{-5} \mathrm{~K}^{-1}$ ) 

    View Solution

Leave a Reply

Your email address will not be published.

error: Content is protected !!
Download App